P Series Configuration

P Series Player Requirements

What is My Player Model?
To find the model of your player, look at the sticker on the bottom of the device.
If the sticker says NUC5i3RYH, the IW player model is INTEL NUCRC3-S-MBRA.
If it says NUC6i3SYH, the model is INTEL NUCSC3-S-MBRA.
Similarly, if the sticker reads

The first step to configuring your Industry Weapon P Series Player is to ensure the necessary hardware connections are in place. This includes a power adapter, DisplayPort/HDMI cable, and an Ethernet connection.

  • A network connection that conforms to our network topology
  • An active Industry Weapon MediaBridge installed onto your network is required for content to synchronize successfully
  • Access to your CommandCenterHD account from a computer
  • Access to the network where the player will be connected

Configuring your P Series Player

  1. Power on your P Series Player and it will pull a DHCP address from your network, and launch into the authorization screen. The DHCP address is displayed at the bottom of the screen prior to an authorization code appearing.*If your player does not display an authorization code once powered on, this means your player does not automatically have cloud access. You’ll have to manually configure the device within the Devices section of CommandCenterHD.

Adding Your P Series Player into CommandCenterHD

  1. On your CommandCenterHD Dashboard hover over the icon Wrench in the upper right and click Devices.
  2. From the Device Manager screen, click Authorize Smart Device.
  1. Enter the authorization code from your player display and then click on the Authorize button
  1. A new window will pop up prompting you to fill out information for this player. Be sure to fill out the required fields listed below:

Player Name
Choose a name to identify this player.

Player Status
Active status will allow the player to sync content.

Choose your screen orientation.

Player Channel
Choose the content Channel you would like this player to display.

Connect Mode
Choose if this player will use a MediaBridge or the Cloud to sync content.

Enter this player’s location and click on the “Get Location” button.

It will then take 5-10 minutes to register and then begin to download the necessary files for playback. Once these are downloaded, you will see content playback on the screen. The player will also apply any new firmware version found during this process, this could take up to 30 minutes.

To check the status of your P Series player, find it in the list of devices on the “Manage Devices” screen in CommandCenterHD. Under the “Status” column, you will see an image of a yellow question mark next to each active player. If you simply click on the question mark next to your player, you will be able to see if your player has made it online or if an error has occurred in the process.

Accessing the P Series Player Web Console

  1. After registering your device in CommandCenterHD, if you need to configure a MediaBridge, or would like to access the player for device management purposes, on a workstation that has network access to your player, open a web browser and enter the IP address displayed on the Industry Weapon Splash Screen into the URL bar.
    Username = admin
    Password = default

You will arrive at the page shown below:

  1. On this page you will see your device already configured to your Account ID, Device ID and Account Pin. Provided your player has access to the cloud, the MediaBridge IP address will be automatically detected, and you can manage your device from here.
    *If your player does not have cloud access, you will need to manually enter in the MediaBridge IP address. This is done under the IP Configuration section, in the MediaBridge IP field.

Enabling Wireless Connectivity on the P Series Player

This process requires a wired network connection in order to access and setup the wireless network connection option. Once the wireless network connection is established, the wired connection can then be disconnected from the player.

  1. On a workstation that has network access to your player, open a web browser and enter the IP address displayed on the Industry Weapon Splash Screen into the URL bar.
    Username = admin
    Password = default
  2. You will arrive at the page shown below:
  1. Navigate to the IP Configuration page by clicking the button on the left of the page.
  2. Change the Interface drop down to the Wireless option and select your wireless network from the generated list that appears.
  3. If this wireless network is password protected, enter the password.
  4. Click on the Save button to save your wireless settings.

Configuring Your P Series Player for WebCache Content

Webcache is normally utilized for customized content integrations, and is not used during standard deployments. In most situations, you will not need to do these configurations.
Note: Your MediaBridge must also be configured for WebCache Content

  1. From the Devices page mentioned above, find your device and click the Edit icon.
  2. Click the Advanced tab on the left and set Enable Web Cache to Enabled. If you are provided a subfolder name, enter it into Web Cache Sub ID.

Touch Screen Calibration

  1. On a workstation that has network access to your player, open a web browser and enter the IP address displayed on the Industry Weapon Splash Screen into the URL bar (Username = admin Password = default). You will arrive at the page shown below:

2. On the menu on the left side of the screen, click on the Touch link (highlighted in orange in the above image).

3.  You will arrive at the below configuration page.

4. Confirm that the 3 fields: Touch Device, Swap Axis, and Invert Axis are set correctly based on your screen.

5. Once your settings are entered click on the Save Axis button.

6. Click on the Calibrate Touch button to launch the touch calibration on the screen attached to this media player.
*Someone must be at the screen to complete this calibration by touching the red X marks that appear on screen.

7. Once the on-screen calibration has been successfully completed, the calibration settings will be saved.
*The Clear Calibration button can be used to reset all saved calibration settings.


Email Industry Weapon Support at support@industryweapon.com or call us at 877-607-0562.

Next Article

Was this article helpful?